Products description
Supergun MAK Strike
Features
- Improved usability : All the user interfaces are now reachable from the side of the PCB.
- Improved SCART support is now designed. It switches automatically to RGB and AV mode.
- Stereo Audio and Mono audio, select between Stereo or Mono with a switch.
- Audio SCART Sound interface and RCA Chinch Audio
- 5V display
- Dip switch for Chamma Support, button 6 for Pandora Box
- Standard MOLEX PC Power Supply Unit plug.
- All signal via Screw Terminals
- On and off switch
- On and off switch status will be indicated by a power LED.
- NEOGEO compatible controller ports.
- Start Player 1, Start Player 2, Coin, Test and Service Tactile Press Button.
- RGB 3 channel potentiometer with one axle : The colors can be adjusted by using RGB 3 channel potentiometer with one axle. This 3 channel potentiometer can be controlled by one axle. Mostly all know supergun uses three different potentiometer. Thus makes it difficult to achieve a clear white level on the screen. By using only one axle for all colors at same time this clear white level is no issue anymore.
- Extended 6 Button Jamma Pinout: The new ArcadeForge Supergun MAK comes with extended 6 Button Jamma Pinout.
The optional enclosure is
- laser cut
- all controls are described with laser engravings
- 3mm strong
The optional Arcade PSU comes with
- EU power plug optimized for Arcade PSU
- Molex Harness optimized for Arcade PSU, 25cm length
- Arcade PSU compatible for 110V and 220V
- 5V adjustable via knob
- 5V, 12V, -5V, 2x GND
| Parts Side | Solder Side | ||
| GND | 1 | A | GND |
| GND | 2 | B | GND |
| +5V | 3 | C | +5V |
| +5V | 4 | D | +5V |
| -5V | 5 | E | -5V |
| +12V | 6 | F | +12V |
| NC | 7 | H | NC |
| Coin Counter 1 | 8 | J | Coin Counter 2 |
| Lock Out 1 | 9 | K | Lock Out 2 |
| Speaker +, Audio L | 10 | L | Speaker - |
| Player 1 Button 6 | 11 | M | Player 2 Button 6 |
| Video Red | 12 | N | Video Green |
| Video Blue | 13 | P | Video Sync |
| Video GND | 14 | R | Service Switch |
| Test Switch | 15 | S | Slam Switch |
| Coin Switch 1 | 16 | T | Coin Switch 2 |
| Player 1 Start | 17 | U | Player 2 Start |
| Player 1 Up | 18 | V | Player 2 Up |
| Player 1 Down | 19 | W | Player 2 Down |
| Player 1 Left | 20 | X | Player 2 Left 2 |
| Player 1 Right | 21 | Y | Player 2 Right |
| Player 1 Button 1 | 22 | Z | Player 2 Button 1 |
| Player 1 Button 2 | 23 | a | Player 2 Button 2 |
| Player 1 Button 3 | 24 | b | Player 2 Button 3 |
| Player 1 Button 4 | 25 | c | Player 2 Button 4 |
| Player 1 Button 5 | 26 | d | Player 2 Button 5 |
| GND | 27 | e | GND |
| GND | 28 | f | GND |
MAK Strike Controller Port Pinout
| DSUB 15 pin | Neo Geo | MAK STRIKE |
| 1 | Ground | Ground |
| 2 | NC | Button 5 |
| 3 | Select | Coin |
| 4 | D | Button 4 |
| 5 | B | Button 2 |
| 6 | Right | Right |
| 7 | Down | Down |
| 8 | 5V | 5V |
| 9 | D | NC |
| 10 | NC | Button 6 |
| 11 | Start | Start |
| 12 | C | Button 3 |
| 13 | A | Button 1 |
| 14 | Left | Left |
| 15 | Up | Up |
Installation
- Plug your Arcade PSU and check voltages with your multimeter. The Arcade PSU gives good values for 5V and 12V
- Plug your Arcade PSU to the Supergun MAKE Strike without any connected game. Check that voltage display shows 5V. Do not proceed if not. Check your wiring.
- Plug your Arcade Game to the Supergun
- Plug your Supergun to your home entertainment system.
- Plug your neogeo compatible controllers
- Turn on unit.
- Enjoy playing.
Customers who bought this product also bought the following products:
Jam
Supergun MAK Strike Power Cable for for Arcade PSUs
This is the last project called Retro TV / SLG Scart. It gives just Scanlines to RGB SCART consoles without any need of additional scaler or sync stripper.
The Jamma Friend RGB Amp boosts the RGB Level of your setup.
Jamma Adapter Sega System 16
This Product was added to our catalogue on 01/04/2021.